Just How to Install a Bath Tub Yourself
Just How to Install a Bath Tub Yourself
Blog Article
We've encountered this article on Installing A Bathtub down the page on the web and thought it made perfect sense to write about it with you on this site.
Installing a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is additionally a reasonably tough job. If the old tub is readily available, the task can relocate immediately; if you need to open up a wall to remove the old bathtub and place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the new one. See to it you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to hiring a contractor to take control of a halfway-completed task, it is much better to consider using one prior to you begin. Chances are you might require a professional plumber to make tube links.
This post will help you mount a new bathtub in your washroom if you have actually already acquired a brand-new tub and also don't need to transform the plan of your previous water supply pipelines.
Your tools and also material checklist must comprise the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted access that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the remaining water that will originate from the pipelines. Once the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the bath tub up until the spirit level reads level.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the appropriate supply pipe by making a compression sign up with; then do the same for the other faucet.
Activate the water as well as inspect all joints as well as new pipework for leaks and tighten them if essential. Load the tub and also examine the overflow outlet and the typical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and also sealing around the bath tub needs to wait up until the tub has been made use of at the very least when as this will certainly resolve it into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub? Try leaving a remark down the page. We'd be glad to know your views about this page. Hoping to see you back again in the near future. In case you enjoyed reading our blog post kindly do not forget to pass it around. We truly appreciate reading our article about Installing A Bathtub.
Call
Report this page